Copaiba oil and vegetal tannin as functionalizing agents for açai nanofibril films: valorization of forest wastes from Amazonia.

The applicability of cellulose nanofibrils (CNFs) has received attention due to their attractive properties. This study proposes the functionalization of açai CNFs with copaiba oil and vegetal tannins to produce films with potential for packaging. Bio-based films were evaluated by vapor permeability, colorimetry, and mechanical strength. CNFs were produced by mechanical fibrillation, from suspensions of bleached açai fibers and commercial eucalipytus pulp. Moreover, copaiba oil and vegetal tannin were added to the CNFs to produce films/nanopapers by casting from both suspensions with concentrations of 1% (based on CNF dry mass). The bulk densities of the eucalyptus CNF films were higher (1.126-1.171 g cm-3) compared to the açai CNF ones. Films from eucalyptus and açai pulps containing copaiba oil and tannins presented higher Tonset and Tmax, respectively (312 and 370 °C). Films with açaí CNFs functionalized with copaiba oil and tannin showed the lowest permeability value (370 g day-1 m-2). Films produced with eucalyptus pulp, and eucalyptus pulp functionalized with copaiba oil highlighted by superior mechanical strength, achieving 133.8 and 121.4 MPa, respectively. The evaluation of colorimetry showed a greater tendency to yellowing for açai films, especially those functionalized with vegetal tannins. Besides the low cost, functionalized vegetal-based nanomaterials could have attractive properties, with potential for application as some kind of packaging, for transporting basic products, such as breads, flours, or products with low moisture content, enabling efficient utilization of forest wastes.

Spent Coffee Grounds as Building Material for Non-Load-Bearing Structures.

The gradual development of government policies for ecological transition in the modern construction sector leads researchers to explore new alternative and low environmental impact materials with a particular focus on bio-sourced materials. In this perspective, the mechanical, thermal insulation, and the sound absorption performances of a spent coffee grounds/potato starch bio-based composite were analyzed for potential application in buildings. Based on thermal conductivity and diffusivity tests, the coffee grounds waste biocomposite was characterized as an insulating material comparable with conventional thermal insulation materials of plant origin. Acoustical tests revealed absorption coefficients in the same range as other conventional materials used in building acoustical comfort. This bio-sourced material presented a sufficient compressive mechanical behavior for non-load-bearing structures and a sufficient mechanical capacity to be shaped into building bricks. Mechanical, thermal, and acoustic performances depend on the moisture environment. The groundwork was laid for an initial reflection on how this composite would behave in two opposite climates: the continental climate of Reims in France and the tropical climate of Belém in Brazil.

Enhancement of the Amazonian Açaí Waste Fibers through Variations of Alkali Pretreatment Parameters.

The açaí fruit depulping produces large amounts of long lignocellulosic fiber bundles that are disposed in the environment. Chemical pretreatments may improve açaí fibers favoring their usage in advanced materials. This work aimed to define optimal alkali reaction parameters to improve the properties of açaí fibers. Two NaOH concentrations (5 % and 10 %) and two reaction temperatures (80 °C and 100 °C) were tested. The raw and treated fibers were analyzed by scanning electron microscopy, Fourier transformed infrared spectroscopy, X-ray diffraction, and thermal analyses. All the alkali pretreatments separated fibers from the bundles, unblocked pit channels by removing silicon structures, exposed the inner lignin, partially removed non-cellulosic compounds, and raised the cellulose crystalline index. The highest temperature and NaOH content resulted in better cleaning and isolation of the fibers, while milder conditions better preserved the cellulose crystalline structure and thermal stability.

Diameter distribution in a Brazilian tropical dry forest domain: predictions for the stand and species.

Currently, there is a lack of studies on the correct utilization of continuous distributions for dry tropical forests. Therefore, this work aims to investigate the diameter structure of a brazilian tropical dry forest and to select suitable continuous distributions by means of statistic tools for the stand and the main species. Two subsets were randomly selected from 40 plots. Diameter at base height was obtained. The following functions were tested: log-normal; gamma; Weibull 2P and Burr. The best fits were selected by Akaike's information validation criterion. Overall, the diameter distribution of the dry tropical forest was better described by negative exponential curves and positive skewness. The forest studied showed diameter distributions with decreasing probability for larger trees. This behavior was observed for both the main species and the stand. The generalization of the function fitted for the main species show that the development of individual models is needed. The Burr function showed good flexibility to describe the diameter structure of the stand and the behavior of Mimosa ophthalmocentra and Bauhinia cheilantha species. For Poincianella bracteosa, Aspidosperma pyrifolium and Myracrodum urundeuva better fitting was obtained with the log-normal function.

Diameter distribution in a Brazilian tropical dry forest domain: predictions for the stand and species

ABSTRACT Currently, there is a lack of studies on the correct utilization of continuous distributions for dry tropical forests. Therefore, this work aims to investigate the diameter structure of a brazilian tropical dry forest and to select suitable continuous distributions by means of statistic tools for the stand and the main species. Two subsets were randomly selected from 40 plots. Diameter at base height was obtained. The following functions were tested: log-normal; gamma; Weibull 2P and Burr. The best fits were selected by Akaike's information validation criterion. Overall, the diameter distribution of the dry tropical forest was better described by negative exponential curves and positive skewness. The forest studied showed diameter distributions with decreasing probability for larger trees. This behavior was observed for both the main species and the stand. The generalization of the function fitted for the main species show that the development of individual models is needed. The Burr function showed good flexibility to describe the diameter structure of the stand and the behavior of Mimosa ophthalmocentra and Bauhinia cheilantha species. For Poincianella bracteosa, Aspidosperma pyrifolium and Myracrodum urundeuva better fitting was obtained with the log-normal function.

Evaluation of reaction factors for deposition of silica (SiO2) nanoparticles on cellulose fibers.

This study aimed to evaluate reaction conditions for deposition of SiO2 nanoparticles on the surface of cellulose fibers and their influence on moisture adsorption of the hybrid organic-inorganic material formed. SiO2 nanoparticle deposition was carried out with the sol-gel process testing four reaction times (2, 12, 18, and 24h) and three contents of the tetraethyl-orthosilicate (TEOS) precursor (1.9, 4.2 and 8.4g g(-1) of cellulose fiber). Modification time and TEOS content directly influence the amount of Si deposited on the fiber surface, nanoparticle diameter distribution, thermal stability, and resistance to moisture adsorption. There is a tendency of slight increase of nanoparticle size and the amount of Si deposited with increasing reaction time. SiO2 nanoparticles were bonded on the surface of the cellulose fibers and are able to improve thermal stability of the material, increasing onset degradation temperature. The moisture adsorption capacity of the modified cellulose fiber was reduced up to 50%.